DIN Controls Display Select [SEL] Feature
applicable to C, 100, 300 & P Series Controls
Future Design Controls provides a manner to customize the sequence of control prompts to meet your specific application and operator needs.
The Select [SEL] feature provides flexibilty for you to select those control parameters which are significant to your application to be displayed in sequence when the scroll key is depressed.
If there are no parameters in the SEL function no prompts are displayed when the scroll key is depressed. Shown below are listing of available prompts by Control Series.
The number of visible prompts from which to select will vary with control configuration; i.e. when a control is configured for on/off control the P, I & D variables will not be shown in the SEL available prompts.
300 Series SEL Functions - 5 prompts maximum
- None
- Time - Dwell Time Setting
- Alarm Setpoint [only Alarm 1 and Alarm 2 will be available dependent upon configuration]
- A1SP - Process Alarm #1 SP
- A1DV - Deviation Alarm #1 SP
- A2SP - Process Alarm #2 SP
- A2DV - Deviationl Alarm #2 SP
- Ramp - Setpoint Ramp Rate
- Ofset - [Proportional Band offset or manual reset]
- REFC - Reference Constant - [specific OEM function - pump application]
- Shift - Bias for adjusting PV display
- PB1 - Proportional Band #1
- TI - Integral #1 [automatic reset of PID]
- TD - Derivative #1 [Rate function of PID]
- CPB - Cooling Proportional Band for Heat/Cool PID
- SP2 - Setpoint #2
- PB2 - Proportional Band #2
- TI2 - Integral #2 [automatic reset of PID]
- TD2 - Derivative #2 [Rate function of PID]
Top of Page
100/C Series SEL Functions - 8 prompts maximum
- None
- Lock - Security Function for operator access to change parameters
- Input - configuration of input type
- Unit - Degress F, C or Units
- Decimal Point - configure display decimal point
- rr - Setpoint Ramp Rate
- Shift - Bias for adjusting PV display
- PB - Proportional Band
- TI - Integral [automatic reset of PID]
- TD - Derivative [Rate function of PID]
- Ofset - Proportional Band offset or manual reset
- CPB - Cooling Proportional Band for Heat/Cool PID
- DB - Deadband adjustment between Output #1 & #2 for Heat/Cool
- O1HY - Output #1 Hysteresis
- O2HY - Output #2 Hysteresis
- Cyc1 - Time Proportioning Cycle Time Adjustment - Output #1
- Cyc2 - Time Proportioning Cycle Time Adjustment - Output #2
- addr - RS232/485 Modbus communication address [100 Series only]
Top of Page
P Series Profile Ramp/Soak Controls - 8 prompts maximum
- None
- Lock - Security Function for operator access to change parameters
- Input - configuration of input type
- Unit - Degress F, C or Units
- Decimal Point - configure display decimal point
- Bias - Bias or shift for adjusting PV display
- Gain - Gain Adjustment
- PB - Proportional Band
- TI - Integral [automatic reset of PID]
- TD - Derivative [Rate function of PID]
- Ofset - Proportional Band offset or manual reset
- CPB - Cooling Proportional Band for Heat/Cool PID
- DB - Deadband adjustment between Output #1 & #2 for Heat/Cool
- O1HY - Output #1 Hysteresis
- Cyc1 - Time Proportioning Cycle Time Adjustment - Output #1
- Cyc2 - Time Proportioning Cycle Time Adjustment - Output #2
- A1HY - Alarm #1 Hysteresis
- A2HY - Alarm #2 Hysteresis
- A3HY - Alarm #3 Hysteresis
- addr - RS232/485 Modbus communication address [100 Series only]
Top of Page
Return to:
Process & Temperature Control Page.htm
300 Series.htm
100/C Series.htm
P Series Profile Controls.htm
Future Design Controls: 888.751.5444 csr@futuredesigncontrols.com
